Přeskočit navigaci

 

Logo Installation - Pion

Pion

Tel. +420 605 721 828
 
 

Our Calculator

Calculating the cost of heating does not require any advanced math so why not find out what the Wattage required to heat
up your space.

More

Why Infrared

Case studies

Comparison of costs

for heating

Proč infra

Workshop / 20 m2

Be a handyman round the year.

 

Workshop

Being a tax advisor is a hard job – Mr. Podlešák spends up to 14 hours at the computer dealing with hundreds of thousands of figures every day. So to relax he goes down to his
workshop in the basement…

More

Comparison of costs

for heating

Proč infra

City Apartment / 62 m2

Now it's really safe for the kids

to play on the floor.

City Apartment

Two months testing showed good results: The floor stayed warm and neither Johnny nor Veronika had even once a cold even though the winter was harsh…

More

Comparison of costs

for heating

Proč infra

Upland Flat / 60 m2

Walking around the flat just in your T-shirt in winter! That’s real indoor climate comfort!

Upland Flat

Mr. Ševčík lives in a 3 bedroom apartment in a beautiful mountain town Lázně Libverda 550 m above sea level, which doesn’t mean just
beautiful environment but
also harsh winters with
outside temperature often
falling below -20 °C…

More

Comparison of costs

for heating

Proč infra

Mountain Cottage / 172 m2

A retired couple has finally found a convenient & cost-effective heating solution for their mountain cottage

Mountain Cottage

More than 20 years ago a couple from Prague fell in love with the nature of the Jizera Mountains. That’s
why they decided to build
a nice cottage there…

More

Contact Us

For free calculation to find out what the Wattage required to heat up your space. Call or email:

Tel.: +420 605 721 828
info@infraline.cz

 

Installation

Thanks to the design of the PION heating unit, its installation is more than simple.

PION infrared heating units are primarily intended for ceilings, because overhead installation can make best use of their unique oval profile plus the 120° curve of the heat-emitting panel and evenly heat up the entire room. This setup is not just the most efficient but it also saves valuable space; with the unit hung below the ceiling you are free to arrange furniture, hang pictures or position other interior accessories as you please, on the walls, the floor or even below the windows, without restriction. The exact positioning and orientation of the unit should be carefully considered prior installation in order to ensure the maximum radiation coverage of the room’s surfaces.

If you hang the heating unit as intended by design, an empty air capsule will form between the ceiling and the top side of the heater, providing natural insulation. Although the temperature of the heat-emitting panel can reach even 250 degrees, the highly effective thermo insulation made from ceramic fibre prevents the unit back-side temperature from going over 80 °C, thus protecting the ceiling from over-heating..

Installation instructions

Obrázek
  • Open the package and take out the heater. Place it on a horizontal surface of your choice with the heat-emitting panel face down.
  • Select a place on the ceiling that is suitable for the unit’s installation and mark the spots where you will screw in or anchor the hooks – please refer to the installation scheme at all times.
  • The heating unit must be connected to a power grid by means of a suitable power cord. The power cord may never be left lying on the heater while its surface is hot - the cable would come to harm!
  • Drive the end of the chain with the wider loop tip into the groove that runs lengthwise along the top side of the casing and drag it to the desired position on either side of the unit.
  • Screw the hooks firmly in and then hang the heating unit by the metallic chains.
  • Before switching the unit on wipe the heat-emitting panel with industrial alcohol.

  • The heater should reach the selected temperature within approximately 8 minutes after switching it on.

Obrázek  

 
Obrázek You may detect odours emanating from the appliance the first time it is used. This happens when the substances used for the conservation of technical parts start burning off. This smell shall, however, disappear shortly and constitutes no cause for concern.
Minimal space and size requirements for mounting the infrared unit

Obrázek

Obrázek

 

A – distance from the ceiling may not be less than 100 mm
B – distance from the walls may not be less than 200 mm
C – distance between the unit and the objects located within the heater’s radiation affected zone may not be less than 250 mm
L – PION model types allow for the distance between the chains (fittings) to be regulated by manual adjustment
H – minimal required height for mounting

 

 

Obrázek

Obrázek
  • Make sure you adhere to the stipulated minimum mounting height (H) during the installation of the heating unit.
  • The standard enclosed fixture set ensures safe mounting of the heater to ceilings with various types of natural surfaces (wood, concrete, metal etc.).
  • In case you wish to mount the unit to a ceiling with an artificial surface finish (e.g. PVC) then standard mounting is allowed only if the plastic material has a thermal tolerance of 80 °C or more.
Power-grid connection instructions

Obrázek
  • The heating unit must be connected to a power grid by means of a power cord with
    a correct and sufficient current capacity.
  • Attach the power cord wire ends to the relevant clips on the heater as indicated.
  • Right from the external casing of the electrical clips the power cord must lead vertically straight up towards the ceiling, parallel to the chains. The power cord may never be left lying on the heater while its surface is hot - the cable would come to harm.
  • Make sure the correct polarity is observed.
  • When connecting the unit to a power grid while using a thermostat the installation must be carried out in compliance with the instructions provided by its manufacturer.
  • The thermostat should be mounted 1.5 meters above the floor.  When selecting its position, avoid draught and such zones that would put the thermostat under direct impact of heat rays or other types of heat sources, should you wish to avoid malfunctions.
Obrázek

 

If you have chosen fixed power grid connection for installing your heating unit, please commission a professional to carry the installation out on your behalf.